- #Volume could not be unmounted imac pro for mac
- #Volume could not be unmounted imac pro mac os
- #Volume could not be unmounted imac pro windows
This will allow Apple's Disk Utility to create its own volumes. There may be other ways to resolve this issue, but the easiest way is to erase the disk and set it up with a GUID scheme.
For more technical information see Apple documentation - here. Apple requires at least 200 MB for this volume which is why this error occurs. It’s caused by Apple trying to use the 134.2 MB Microsoft Reserved volume for their EFI volume. This error can occur when either erasing or partitioning the disk. Instructions for HFS+ formatting can be found here.Įrror Message - MediaKit reports not enough space
#Volume could not be unmounted imac pro mac os
If you are using this drive for macOS only, then reformat the drive Mac OS Extended (Journaled) also referred to as HFS+ for best compatibility. Instructions for ExFAT formatting can be found here. If you are using this drive between macOS and Windows, back up any important data on the drive and reformat the drive ExFAT on macOS.
#Volume could not be unmounted imac pro windows
If you need to go between Mac and Windows then you would want to select ExFAT. For example Mac OS Extended (Journaled) or APFS.
#Volume could not be unmounted imac pro for mac
If you are using it for Mac only then select a format specifically for macOS. To resolve this, you must first erase the disk and set the Scheme to GUID Partition Map. If you hover your mouse over the partition button you can see the tooltip provided by Apple. The button is greyed out because the drive is set up as MBR which is typically used for drives less than 3 TB. This was first seen in macOS 10.11 (El Capitan) and has continued. If you will be going between Mac and Windows then there should be no issues. If you plan on using the drive for Mac only then you will want to erase the disk. For more technical information see Microsoft documentation - here. This is typical and not an issue when using the drive as NTFS. It is shown as Microsoft Reserved in Disk Utility. This volume exists because the drive is set up for Windows using GUID/ NTFS. What is that 134.2 MB volume on the drive? Which is why selecting the non-indented entry is important when formatting the drive. This is important because when erasing the drive you will get different options depending on whether you have the volume or disk selected. The indented entries directly below are the volumes (partitions). The non-indented entry is the physical disk which typically has Media in the name. You should see at least two, sometimes three, entries for your drive depending on how it is formatted. If you are running 10.12 or 10.11 this step is not required as the option is not available. Change the view to Show All Devices instead of the default which is Show Only Volumes. If you are running macOS 10.13 (High Sierra) or later it is important to change the view in Disk Utility. Note: Reformatting the drive will erase all data on the drive, so you should copy any data you want off the drive prior to formatting. Not sure what version you are using? Click here to determine your version of macOS. This article applies to the following versions of macOS: The following is not an exhaustive list of error messages, so you may not find your specific error here. Note: Make sure you have closed all applications that may be using the volume you want to eject, and that the volume is not in use.This article covers some of the common error messages and questions you might encounter while using Disk Utility. I’ve found that the first method is much more successful – I’ve had the disk fail to unmount more than once using the Terminal command. Just replace DISK_NAME with the name of the volume you want to eject, press enter, and you’re done! If you’re sure that’s not the case, then click “Force Eject…”, and Voila! That’s all there is to it! Method 2įor those of you that prefer using Terminal, or would rather eject the drive with a single command, simply open Terminal, and type the following:ĭiskutil unmountDisk force /Volumes/DISK_NAME You may see a message like the one above, telling you that there may be a program using that volume. The easiest and safest way to force a volume to eject is to open a new Finder window, locate the drive or volume in the left-hand column, right-click or option-click the volume, and select Eject “” in the drop down menu. Sometimes this is because a program is using a file on the volume in question, but other times the volume just seems to be stuck! Fortunately, there’s an easy solution! We’ll show you two ways to force your Mac to let go! Method 1
Sometimes OS X doesn’t want to let you eject a volume or an external drive.